Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADITER B RVA150 100 NT - (PBT+ASA)-GF15 - RadiciGroup High Performance Polymers

Check here, which other Raditer B RVA datasheets, application examples or technical articles are available in Material Data Center

Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses - Fonctions

Any use of this information falls under the rules of our disclaimer.

Informations produit

PBT/ASA blend, 15% glass fibre reinforced injection moulding grade. Natural colour.

Suitable for parts requiring medium stiffness and improved mechanical resistance, reduced shrinkage and low warpage. Good surface aspect.

Caractéristiques des transformations/physiques	Valeur	Unité	Norme du test
ISO Data
Retrait au moulage, parallèle	0.4	%	ISO 294-4, 2577
Retrait au moulage, perpendiculaire	0.6	%	ISO 294-4, 2577

Propriétés mécaniques	Valeur	Unité	Norme du test
ISO Data
Module en traction	5600	MPa	ISO 527
Contrainte à la rupture	105	MPa	ISO 527
Déformation à la rupture	3.3	%	ISO 527
Résistance au choc Charpy, +23°C	60	kJ/m²	ISO 179/1eU
Résistance au choc Charpy (entaillé), +23°C	7	kJ/m²	ISO 179/1eA

Propriétés thermiques	Valeur	Unité	Norme du test
ISO Data
Température de fusion, 10°C/min	222	°C	ISO 11357-1/-3
Température de fléchissement s/chrg, 1.80 MPa	145	°C	ISO 75-1/-2
Inflammabilité pr. épaisseur h	HB	class	IEC 60695-11-10
Epaisseur de l'éprouvette	1.6	mm	-

Propriétés électriques	Valeur	Unité	Norme du test
ISO Data
Résistivité transversale	1E13	Ohm*m	IEC 62631-3-1

Propriétés diverses	Valeur	Unité	Norme du test
Masse volumique	1340	kg/m³	ISO 1183

Fonctions

Caractéristiques

Transformation

Moulage par injection

Conditionnement

Grains, Couleurs naturelles

Additifs

Agent de démoulage

Caractéristiques

Bas gauchissement

Disponibilité régionale

Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique

Autres informations

Moulages par injection

The material is delivered in moisture-proof packaging. It is important to dry the material prior to processing: maximum recommended water content is 0.02%. Typical conditions with a desiccant drier: temperature 120 ° C, dew point -40 ° C or below, time 2-4 h or more. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters

Melt Temperature	Mold Temperature	Injection Speed
250 - 280°C	80 - 90°C	medium-high

Conditions générales

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.